Framing Parameters of an Interior Wall

You can select the framed interior wall's parameters used in the wall panel design by clicking the Framing button in the Wall Selection dialog box. Parameters are customer-specific. Some basic parameters are described in this guide.

• Frame, Gen
• Frame, Plate, Blocks
• Frame, Openings
• Frame, Sheathing

Frame, Gen

On this tab, you can define the parameters required in wall panel design (included in the Vertex BD Framer product). The default values for the parameters are read from the building parameters.

Framing Detail

Select from the list.

Panel Label

The first part of the wall panel label.

Ext, Corner Type, Int. Corner Type, Backer

Details of a rectangular corner and backers. Click the Sel button, and select a detail from a drawing window by clicking the hot spot. The detail of an angled corner is defined in the building parameters.

Stud Spacing

The distance between the studs of a wall panel measured from center to center. Select from the list.

Stud Start From

The starting point of the studding of a wall panel. Select the radio button Right, Left, Center or Left/Right. The right and left of the wall are determined by the viewing direction.

Center Stud

The center stud of a wall panel can be either a single or a double stud. Select the radio button Single or Double.

Frame, Plate, Blocks

On this tab, you can define the parameters required in wall panel design (included in the Vertex BD Framer product). The default values for the parameters are read from the building parameters.

Top Type

Click the Sel button, and select a detail from a drawing window by clicking the hot spot.

Top Plate

Select the cross section from the profile library by clicking the Sel button.

Part Properties

If you select an option with a beam, also select the Beam Along Top Pl. cross section from the profile library by clicking the Sel button.

Head binder

Select the cross section from the profile library by clicking the Sel button.

Part Properties

Bot. Type

Click the Sel button, and select a detail from a drawing window by clicking the hot spot.

Bottom plate

Select the cross section from the profile library by clicking the Sel button.

Part Properties

If you select an option with a beam, also select the Beam Along Bottom Pl. cross section from the profile library by clicking the Sel button.

Stud

Select the cross section from the profile library by clicking the Sel button.

Part Properties

Select single or double studs by selecting an option from the No list.

Block

Select blocking by selecting the check box Horiz. (A) or End (B), or both.

Select the cross section of the blocking by clicking the Sel button. Select the position height of the blocking from the Height list, or type the height in relation to the floor base height in the text field.

Select the Type of the blocking from the list:

Frame, Openings

On this tab you can select the window and door details to be used in the wall panel design.

Header #1, #2, #3

The use of the details is determined as follows:

• Detail Header #1 is used when the width of the opening is smaller than or equal to the value in the Max field on the same row.
• When the width of the opening exceeds the maximum width of Header #1, detail Header #2 is used.
• When the width of the opening exceeds the maximum width of Header #2, detail Header #3 is used.

Click the Sel button, and select a detail from a drawing window by clicking the hot spot.

Select the cross section of the beam to be used in the opening details from the profile library by clicking the Sel button.

Part Properties

Select the maximum width of the opening from the Max list.

Cripple Stud

Select the cross section of the cripple stud from the profile library by clicking the Sel button. Select the number of the cripple studs from the list.

Side Stud

Select the cross section of the side stud from the profile library by clicking the Sel button. Select the number of the side studs from the list.

Frame, Sheathing

On this tab, you can select the parameters of the sheathing to be used in the wall panel design. Select the sheets from the sheathing library by clicking the Sel button. Move the cursor on the desired row in the Sheathing Properties database view, and click the OK button. The parameters on the Sheathing tab are also updated.

Interior Finish

The interior sheathing of the wall.

Sec. Int. Sheathing

The interior sheathing of the frame.

Structural Sheath.

The exterior sheathing of the frame.

Sheathing

The sheathing on the exterior side of the wall.

Overlap, top

If necessary, define the part (a) of the sheet or vertical nailer overlapping the top edge of the wall panel. Enter the desired value in the text field.

Overlap, bottom

If necessary, define the part of the sheet or vertical nailer overlapping the bottom edge of the wall panel. Enter the desired value in the text field.

Installation space

If necessary, define the installation space (d) of the sheathing. Enter the desired value in the text field.